bracket pole

By simulation and calculation,the influence of cross sustaining device to the dynamic character of bogie is basically discussed via the SIMPACK software.

運用SIMPACK動力學軟件 ,通過模擬計算 ,僅就交叉支撐裝置對轉向架動力學性能的影響進行了初步探討。

By the dynamic stress test, the stress spectrum of cross sustaining device s weaking section is obtained, then the loads of cross sustaining device for the speed increased freight car in utilizing condition is identified, which offer the foundation for the load of the fatigue test.

通過動應力測試得到交叉支撐裝置疲勞薄弱部位在線路運行中的應力譜,從而識別出提速貨車交叉支撐裝置在運用工況下的載荷,為其室內疲勞試驗加載提供依據。

The result can offer the foundation for evaluating the fatigue reliability of cross sustaining device.

交叉支撐裝置是提速貨車轉向架的關鍵部件之一。

The meaning and methods to detect the normal position deviation of the cross-braced bogie are discussed.

論述了對交叉支撐式轉向架進行正位偏差檢測的意義和方法 ,介紹了測量系統的設計原理、結構和特點。

Some new techniques applied at present in the three new types of speed increased freight car bogies of cross-braced type, tilting type and Sheffield radial type are described.

對當前交叉支撐型、擺動型、謝菲爾徑向型 3種新型提速貨車轉向架中所采用的一些新技術進行了介紹。

Described are the structure characteristics and key technical parameters of the lower cross-braced bogie.

介紹了下交叉支撐轉向架的結構特點和關鍵技術參數,對側架導框的加工、側架與支撐座的組焊和轉向架的組裝工藝等著重進行了分析。

The results are achieved through comparing the results of the models,such as the solid model with whole infilled wall,solid model of walls with opening,model of crossed steel brace,model of steel frame without braces.

為了在實際工程設計中進行簡化計算,采用交叉鋼支撐模型模擬內填墻的受力特性,并將計算結果同有限元實體模型進行比較,得出了一些結論和建議。

The Study of Bogie Frame Brace Welding Process and Fatigue Life;

轉向架交叉支撐裝置焊裝工藝與疲勞壽命研究

Introduction and Development of Frame-Braced Device Adopted on K2 Bogie;

轉K2型轉向架交叉支撐裝置引進與研制

Research on Bogie Frame Brace Manufacturing Process and Fatigue Life;

提速貨車轉向架下交叉支撐裝置制造工藝與疲勞壽命研究

Analysis & Research on Failure of Frame Braced Bogie for Higher Speed Railway Freight Car;

鐵路提速貨車轉向架交叉支撐裝置失效分析研究

pylon diagonal drag brace

吊臂架交叉阻力支撐條

A pillar, rectangular in cross section, supporting an arch or roof.

支柱交叉處的長方形柱子，支撐一個拱頂或屋頂

Influence of value assigning of inner forces in cross-braced frame on its anti-seismic behavior

交叉支撐內力取值方法對結構抗震性能的影響

a device that supports a football off the ground preparatory to the kickoff.

準備踢球時支撐足球離地的裝置。

"Entry strip support table, looper roll and four-point centering device. "

進料支撐臺,跳動輥,四點對中裝置。

Terminal fittings transmit their force in bearing.

端部連接器將其力傳到支撐裝置上去。

Research and application of the temporary top-supporting device depending on the wall

壁支撐式臨時護頂裝置的研制與應用

Elimination of Looseness and Impact of the Converter Supporting Equipment under High-Temperatureure

梅鋼轉爐支撐裝置高溫松動沖擊控制

Lectotype and Improvement of Safety Supporting Device of Dump Truck

自卸汽車安全支撐裝置的選型與改進

Optimum design of support devices in large-scale columns (Ⅱ)

大型塔器支撐裝置的優化設計(下)

Optimum design of support devices in large-scale columns(Ⅰ)

大型塔器支撐裝置的優化設計(上)

A forked device or part.

分叉裝置，分叉部分

“Research on Strategy and Management of E-business”, IBM SUR(Shared University Research) Project.

“電子商務的支撐環境”，復旦大學電子商務交叉學科重點課題。

Study on Shear Performance of High Strength Cold-Formed Thin-Walled Steel Framing Walls with Cross-Bracing;

高強冷彎薄壁型鋼骨架帶交叉支撐墻體抗剪性能研究